> Connecting (Power On) > Pairing (Registering a device)
Pairing (Registering a device)
The method of operation varies depending on the connection.
Pairing for the First Time
-
1Take out both sides of the earphones.
-
-
After the earphones are taken out, the L (left) and R (right) indicators light up in blue for 1 second, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash slowly.
-
After a short while, the L indicator starts to flash quickly and alternately between red and blue, and a voice message saying “pairing” can be heard from the L earphone.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
For this product, the L earphone is the master unit. In other words, the L earphone is used to connect to a device as well as the R earphone.
-
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
3Select “HA-ET90BT” from the device list.
-
After connection is established, both the L and R indicators will flash slowly in blue, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
-
1Press and hold the button on both the L and R earphones at the same time for 2 seconds.
-
2The power of the L and R earphones turns on. When the L indicator starts to flash quickly and alternately between red and blue (or when a voice message saying “pairing” is heard from the L earphone), release your finger from the button.
-
If the L indicator does not flash alternately between red and blue, turn off the power of the earphone and repeat the steps. Power Off
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “HA-ET90BT” from the device list.
-
After connection is established, both the L and R indicators will flash slowly in blue, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
Pairing the Second and Subsequent Devices
-
1Turn off the Bluetooth function of the device that was last paired.
-
2Take out both sides of the earphones.
-
-
After the earphones are taken out, the L and R indicators light up in blue for 1 second, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash slowly.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
3Press and hold the button on the L earphone for about 2 seconds.
-
Pressing and holding down the button on the L earphone for about 4 seconds turns off the power of the earphones. If the power is turned off, place them back in the charging case and repeat the steps from the beginning.
-
4When the L indicator starts to flash quickly and alternately between red and blue (or when a voice message saying “pairing” is heard from the L earphone), release your finger from the button.
-
5Turn on the Bluetooth function of the BLUETOOTH device.
-
6Select “HA-ET90BT” from the device list.
-
After connection is established, both the L and R indicators will flash slowly in blue, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
-
1With the power of the earphones turned off, press and hold the button on the L earphone for about 7 seconds.
-
Pressing and holding down the button on the L earphone for about 15 seconds initializes the settings of the earphones. In this case, perform the steps in Pairing (Registering a Device) again after the L and R earphones are initialized. Restoring the settings to the initial state
-
2When the power of the L earphone turns on and the L indicator starts to flash quickly and alternately between red and blue (or when a voice message saying “pairing” is heard from the L earphone), release your finger from the button.
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “HA-ET90BT” from the device list.
-
When the L earphone is successfully connected to the device, the L indicator starts to flash slowly.
-
5Press and hold the button on the R earphone for about 2 seconds. The R indicator lights up in blue for 1 second and the power turns on. Release your finger after the R indicator lights up. It is now connected to the L earphone.
-
After connection between the L and R earphones is established, the R indicator will flash slowly in blue, and the earphones can now be used for listening to music.
Pressing and holding down the button on the R earphone for about 15 seconds initializes the settings of the earphones. In this case, perform the steps in Pairing (Registering a Device) again after the L and R earphones are initialized. Restoring the settings to the initial state