No sound from both sides of the earphones

both_sides_sound_none

Check the state of the earphones.
Remove the earphones from the charging case and check the status of the indicators.

The earphones are properly connected to the device.
Check the app settings and volume.

Apps and Volume Control on the Connected Device

  1. Open an app and play

    2. app_01
    app_02

  2. Adjust the volume

    3. volume_smp_1

Select the state after checking

Thank you for using Troubleshooting Guide.

Restoring the earphones to the initial settings and re-establishing the connection may help to solve the problem.

Follow the steps below to check whether there is any abnormality with the sound output.

Restoring settings to the initial state

Start by deleting the registration information of this unit from the BLUETOOTH setting on the BLUETOOTH device. Charge the charging case.

Remove the earphones once if they are inserted into the charging case.

To restore the factory settings, follow the steps below to initialize the settings of both the L and R earphones.

  1. Insert the L and R earphones into the charging case

    2. charging_1_A25T

Start by restoring the settings of the L earphone to the factory default.

  1. Remove both earphones from the charging case and place only the L earphone back in again

    2. take_out_A25T
    charging_1_L_A25T

    After a few seconds, the indicator on the L earphone and charging case will light up.

    charging_2_L_A25T

    Click here if the indicators do not light up or start flashing ＞＞

  2. Touch and hold the touch sensor area on the L side of the earphones for about 15 seconds to initialize

    3. Initializing_L_A25T + Initializing_L_A25T

    Touch sensor area

    Release your finger after the indicator on the L side blinks twice.

    If the indicator doesn’t flash, perform the initialization process again from the start.

Next, restore the settings of the R earphone to the factory default.

  1. Insert the R earphone into the charging case

    2. charging_1_R_A25T

  2. Touch and hold the touch sensor area on the R side of the earphones for about 15 seconds to initialize

    3. Initializing_R_A25T + Initializing_R_A25T

    Touch sensor area

    Release your finger after the indicator on the R side blinks twice.

    If the indicator does not flash, repeat from the start of step 5 again.

  3. Remove both earphones at the same time

    4. take_out_A25T

    The indicator on both earphones lights up and the power turns on.

    After a short while, the indicator on one earphone will flash every 5 seconds and the indicator on the other earphone will flash quickly. The earphones are now ready for device pairing.

    After taking out the earphones, move the L and R earphones close to the device to pair with.

Connecting to a Device

    Turn on the BLUETOOTH connection setting of the device and select “JVC HA-A18T”
    connecting_smp_1
    connecting_smp_2
    connecting_smp_3 + Device List JVC Nav

    JVC HA-A18T

    blue_flash_A25T

    The earphones are connected to the device if the indicators on both sides of the earphones are flashing every 5 seconds.

Apps and Volume Control on the Connected Device

  1. Open an app and play

    2. app_01
    app_02

  2. Adjust the volume

    3. volume_smp_1

Select the state after checking

Thank you for using Troubleshooting Guide.

There seems to be a problem with the product.
If you require more assistance, please contact your local JVC customer support.

The power is off if there is no light on the earphone.

Check whether the power of the earphones can be turned on.

Turn on the power of the earphones

Touch and hold the touch sensor of the earphone that is not lighted up for about 3 seconds.
PLAY_button_L_A25T + SPNV_Button L_A25T

Touch sensor area

The L side of the earphone is used in the illustration above.

The power of the earphones is on if the L and R indicators are flashing (regardless of how the light flashes).

Select the state after checking

Return to the top of the page and re-select the pattern in which the indicators are flashing.

The charging case and earphones have run out of power.

Charge the earphones followed by reconnecting to check whether sound can be heard properly.

Charging the earphones

  1. Charge the charging case

    2. charging_2_No-PC_charge_A25T + Charge_2_A25T

    5V TYPE

  2. Insert the earphones into the charging case

    3. charging_1_A25T
    charging_2_A25T

    The earphones power off and charging starts.

    During charging, the indicators on the earphones light up. Also, the indicator light on the charging case will turn on for a few seconds.

    When charging the earphones or charging case that have not been used for a long period of time, it might take some time for the indicators to light up. Wait for the indicators to light up.

    Click here if the indicators do not light up or start flashing ＞＞

    When charging is complete, the indicators on the earphones will turn off.

Connecting to a Device

  1. Remove both earphones at the same time

    2. Be careful not to touch the touch sensor area when taking them out.

    Case_button_LR_A25T + SPNV_Case_button_A25T

    Touch sensor area

    The indicator on both earphones lights up and the power turns on.

    After a short while, the indicator on one earphone will flash quickly and repeatedly and the indicator on the other earphone will flash twice slowly and repeatedly. The earphones are now ready for device pairing.

    After taking out the earphones, move the L and R earphones close to the device to pair with.

  2. Turn on the BLUETOOTH connection setting of the device and select “JVC HA-A18T”

    3. connecting_smp_1
    connecting_smp_2
    connecting_smp_3 + Device List JVC Nav

    JVC HA-A18T

    blue_flash_A25T

    The earphones are connected to the device if the indicators on both sides of the earphones are flashing every 5 seconds.

Apps and Volume Control on the Connected Device

  1. Open an app and play

    2. app_01
    app_02

  2. Adjust the volume

    3. volume_smp_1

Select the state after checking

Thank you for using Troubleshooting Guide.

If there is no sound although the indicators are flashing, return to the top of the page and re-select the pattern in which the indicators are flashing.

The earphones may not have been properly charged.
Please check the following.

Unable to charge ＞＞

Restoring the earphones to the initial settings and re-establishing the connection may help to solve the problem.

Follow the steps below to check whether there is any abnormality with the sound output.

Restoring settings to the initial state

Start by deleting the registration information of this unit from the BLUETOOTH setting on the BLUETOOTH device. Charge the charging case.

Remove the earphones once if they are inserted into the charging case.

To restore the factory settings, follow the steps below to initialize the settings of both the L and R earphones.

  1. Insert the L and R earphones into the charging case

    2. charging_1_A25T

Start by restoring the settings of the L earphone to the factory default.

  1. Remove both earphones from the charging case and place only the L earphone back in again

    2. take_out_A25T
    charging_1_L_A25T

    After a few seconds, the indicator on the L earphone and charging case will light up.

    charging_2_L_A25T

    Click here if the indicators do not light up or start flashing ＞＞

  2. Touch and hold the touch sensor area on the L side of the earphones for about 15 seconds to initialize

    3. Initializing_L_A25T + Initializing_L_A25T

    Touch sensor area

    Release your finger after the indicator on the L side blinks twice.

    If the indicator doesn’t flash, perform the initialization process again from the start.

Next, restore the settings of the R earphone to the factory default.

  1. Insert the R earphone into the charging case

    2. charging_1_R_A25T

  2. Touch and hold the touch sensor area on the R side of the earphones for about 15 seconds to initialize

    3. Initializing_R_A25T + Initializing_R_A25T

    Touch sensor area

    Release your finger after the indicator on the R side blinks twice.

    If the indicator does not flash, repeat from the start of step 5 again.

  3. Remove both earphones at the same time

    4. take_out_A25T

    The indicator on both earphones lights up and the power turns on.

    After a short while, the indicator on one earphone will flash every 5 seconds and the indicator on the other earphone will flash quickly. The earphones are now ready for device pairing.

    After taking out the earphones, move the L and R earphones close to the device to pair with.

Connecting to a Device

    Turn on the BLUETOOTH connection setting of the device and select “JVC HA-A18T”
    connecting_smp_1
    connecting_smp_2
    connecting_smp_3 + Device List JVC Nav

    JVC HA-A18T

    blue_flash_A25T

    The earphones are connected to the device if the indicators on both sides of the earphones are flashing every 5 seconds.

Apps and Volume Control on the Connected Device

  1. Open an app and play

    2. app_01
    app_02

  2. Adjust the volume

    3. volume_smp_1

Select the state after checking

Thank you for using Troubleshooting Guide.

There seems to be a problem with the product.
If you require more assistance, please contact your local JVC customer support.

Top of page