Menu screen for adjusting the quality of camera images.
Camera Process Menu
This item cannot be selected in the Media mode.
Color Space
For configuring the color space that is used inside the camera.
The gamma and color gamut change automatically according to the selected color space.
When [System] is configured to a setting other than “SD” and “SD(SDI In)”
J-Log1:
Color space that supports 800% dynamic range and log gamma
HLG:
Color space that supports the ITU2100 HLG HDR
ITU2020:
Color space that supports the ITU2020 wide color gamut
ITU709:
ITU709 color space
[Setting Values: J-Log1, HLG, ITU2020, 
ITU709]
When [System] is set to “SD” or “SD(SDI In)”
ITU601 (EBU):
Color space that supports the EBU color gamut
ITU601 (170M):
Color space that supports the SMPTE170M color gamut
ITU709:
ITU709 color space
[Setting Values: ITU601 (EBU), ITU601 (170M), ITU709]
Memo
When [System] is set to “HD” and when “J-Log1” or “HLG” is selected, some menu items under [Camera Process] cannot be configured.
The AE function does not function when “J-Log1” or “HLG” is selected. When the [AUTO IRIS] switch on the lens is set to “AUTO”, the iris is fixed at “F4”.
Colorimetry
For configuring the standard for converting R, G, B signals to Y, Cb, Cr signals when [Color Space] is configured to “HLG” or “ITU2020”.
ITU2020:
Records and outputs ITU2020 RGB signals using the Y-Cb-Cr signal conversion coefficient.
ITU709:
Records and outputs ITU709 RGB signals using the Y-Cb-Cr signal conversion coefficient.
[Setting Values: ITU2020, ITU709]
Memo
This item is available when [Color Space] is set to “HLG” or “ITU2020”.
This is fixed at “ITU709” when [Color Space] is set to “J-Log1” or “ITU709”.
This is fixed at “ITU601” when [System] is set to “SD”.
Gamma
For adjusting the gamma curve that determines the gradation expression.
Cinema 2:
Sets to a gamma curve with soft expression giving priority to high luminance gradation.
Cinema 1:
Sets to a gamma curve with similar gradation to the screen characteristics of movies.
Standard:
Sets to a standard gamma curve.
Off:
Does not perform adjustment.
[Setting Values: Cinema 2, Cinema 1, Standard, Off]
Memo
[Gamma] cannot be configured when [Color Space] is set to “HLG” or “J-Log1”. “HLG Gamma” is used during “HLG” and “J-Log1 Gamma” is used during “J-Log1”.
Level
The amount of correction can be specified separately when [Gamma] is set to “Standard”, “Cinema 1” or “Cinema 2”.
When [Gamma] is set to “Standard”
[Setting Values: 0.35 to 0.45 to 0.55 (in steps of 0.01)]
Increase the number:
Finer gradation at bright areas and coarser gradation at dark areas.
Decrease the number:
Finer gradation at dark areas and coarser gradation at bright areas.
When [Gamma] is set to “Cinema 1” or “Cinema 2”
[Setting Values: +10 to 0 to -10]
Increase the number:
Finer gradation at dark areas and coarser gradation at bright areas.
Decrease the number:
Finer gradation at bright areas and coarser gradation at dark areas.
Memo
When [Gamma] is set to “Standard” with the value set at [0.45], the gamma adjusted conforms to ITU709 or ITU2020.
If [Gamma] is set to “Cinema 2”, the maximum peak signal decreases from 109% as the number becomes smaller in the setting values from 0 to -10. When the level is at -10, the video input with a dynamic range of 600% will be kept within a 100% output.
The level cannot be configured when [Gamma] is set to “Off” or [Color Space] is set to “HLG” or “J-Log1”.
Detail
For adjusting the contour (detail) enhancement level.
Increasing the value increases the sharpness of the contour.
[Setting Values: +20 to -20, Off] (Default Value: -6 for “J-Log1” and “HLG” of Color Space; 0 for all other settings)
Memo
The setting values of this item and [Adjust...] are stored separately when [Color Space] is set to “HLG” or “J-Log1”.
Adjust...
For specifying the detailed settings of the contour (detail).
Memo
This item cannot be selected when [Detail] is set to “Off”.
Master Black
For adjusting the pedestal level (master black) that serves as the reference black.
Increasing the value increases the pedestal.
[Setting Values: +50 to -50 ( 0)]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1”.
The setting value of this item is stored separately when [Color Space] is set to “HLG”.
Black Paint
For adjusting the R (red) and B (blue) components of black.
[Setting Values: +50 to +1, 0, -1 to -50]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG”.
Flare
Performs flare correction.
[Setting Values: On, Off]
Master Flare
Performs correction to prevent the entire image from turning white due to light that enters the lens. The image appears blacker with a larger value, and whiter with a smaller value.
[Setting Values: +20 to +1, ( 0), -1 to -20]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG”.
Flare Balance
For adjusting the balance between R (red) and B (blue).
[Setting Values: +10 to +1, ( 0), -1 to -10] (R/B)
V. Shading
For adjusting shading (color shift) in the vertical direction which occurs due to the lens characteristics.
On:
For adjusting shading.
Off:
Fixes shading adjustment. Manual adjustment is not allowed.
[Setting Values: On, Off]
Adjust
Performs vertical shading adjustment when [V. Shading] is set to “On”.
[Setting Values: -128 to 0 to +127]
Black Toe
Process the dark areas according to the balance of bright and dark areas in the image to adjust the overall balance of contrast.
For altering the gain of dark areas. Adjust this item according to the condition of the captured video signals.
Stretch:
Increases the gain of dark areas in an image to stretch the signals of these areas only, thereby showing the contrast between bright and dark areas more clearly.
Specify the amount of stretch with [Stretch Level].
Normal:
Normal condition.
Compress:
Compresses the gain of dark areas to increase the contrast when the entire image appears bright and contrast is weak. Specify the compression amount with [Compress Level].
[Setting Values: Stretch, Normal, Compress]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG”.
When “Black Stretch” or “Black Compress” is assigned to the [USER2] switch, priority is given to the user button setting and configuration using the menu is disabled.
Stretch Level
Stretch amount increases when a larger value is specified.
[Setting Values: 5 to 1 ( 3)]
Memo
This item is displayed only when [Black Toe] is set to “Stretch”. Otherwise, this item appears as “---” and cannot be selected.
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG”.
Compress Level
Compression amount increases when a larger value is specified.
[Setting Values: 5 to 1 ( 3)]
Memo
This item is displayed only when [Black Toe] is set to “Compress”. Otherwise, this item appears as “---” and cannot be selected.
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG”.
Knee Level
For specifying the start point (knee point) for compressing the video signal to show the gradation of the highlighted portion. Set the [OUTPUT] switch to “AUTO KNEE OFF”.
[Setting Values: 109.0%, 107.5%, 105.0%, 102.5%, 100.0%, 97.5%, 95.0%, 92.5%, 90.0%, 87.5%, 85.0%, 82.5%, 80.0%, 77.5%, 75.0%, 72.5%, 70.0%]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG” and when [Gamma] is set to “Cinema 2”.
Auto Knee Sensitivity
For configuring the response speed of the knee operation when the [OUTPUT] switch is set to “AUTO KNEE ON”. Set to “Slow” when shooting an object under a condition where there is drastic change in the light intensity.
[Setting Values: Fast, Middle, Slow]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG” and when [Gamma] is set to “Cinema 2”.
Auto Knee Peak Filter
For configuring the response speed of the knee operation with respect to a high-luminance point light source and the like when the [OUTPUT] switch is set to “AUTO KNEE ON”.
[Setting Values: High, Middle, Low]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1” or “HLG” and when [Gamma] is set to “Cinema 2”.
White Clip
For setting the point to apply white clip for video signals with a high luminance level.
[Setting Values: 109% to 90% ( 109%)]
Memo
Set this item to 100% if the screen becomes too white with a setting value above 100% or when the system in use limits Y signals within 100%.
The setting value of this item is stored separately when [Color Space] is set to “HLG” or “J-Log1”.
RGB Gamut Clip
For configuring whether to the clip the RGB signals at the same time when clipping the luminance signal using the settings in [White Clip].
On: Performs gamut clipping using the settings in [White Clip] for video signals with a high RGB signal level. Performs gamut clipping according to the settings in [White Clip] for negative signal levels.
[Setting Values: On, Off]
Memo
The area that is subject to gamut clipping when “On” is configured is as follows.
Example:
[White Clip] 103 %
・RGB signal: 103 % or above
・Negative level: -3 % or below
[White Clip]100 % or below
・RGB signal: Equivalent to or higher than the preset value in [White Clip]
・Negative level: 0 % or below
When RGB gamut clipping for EBU-R103 is supported, this feature can be configured to “On” and the value of [White Clip] can be adjusted to a desired level that is 104 % or lower.
The setting value of this item is stored separately when [Color Space] is set to “HLG” or “J-Log1”.
Chroma Clip
For configuring the point to apply chroma clipping for video signals with a high color difference level.
[Setting Values: 113% to 90% ( 113%)]
Memo
When this is set to 100%, the Cb-Cr signal will be clipped so that it falls within the 64-960 range of the ITU 10-bit video standard.
When [Color Space] is set to “HLG” or “J-Log1”, the settings will be saved separately.
White Balance...
Menu for adjusting white balance.
For details, refer to “Adjusting the White Balance ”.
Color Matrix
For setting the color matrix.
Natural:
Sets to a brighter and more natural color matrix than the standard. Effective for shooting under a strong single color light source such as stage lightings.
Cinema Subdued:
Sets to a subdued color matrix that is similar to the screen characteristics of movies.
Cinema Vivid:
Sets to a vivid color matrix that is similar to the screen characteristics of movies.
Standard:
Sets to a standard color matrix.
Off:
Sets the color matrix function to Off.
[Setting Values: Natural, Cinema Subdued, Cinema Vivid, Standard, Off]
Memo
This item cannot be configured when [Color Space] is set to “J-Log1”.
This is fixed at “Standard” when [Color Space] is set to “HLG”.
Adjust
This item is used to adjust [Color Matrix] to a color according to the user’s preference.
The adjusted values of “Natural”, “Standard”, “Cinema Vivid”, and “Cinema Subdued” in [Color Matrix] can be stored individually.
Linear Adjust:
The saturation, hue and brightness of the primary and complementary colors (6 colors in total) can be set individually when “On” is configured.
Multi Adjust:
The saturation and hue of the 16 hue axes (R/R+/Mg-/Mg/B-/B/B+/Cy-/Cy/Cy+/G-/G/G+/Yl/Yl+/R-) can be set when “On” is configured.
When the USER1 button is pressed while the multi adjustment screen is displayed, only the colors of the hue under adjustment remain in the following cases. The other colors become black and white.
LCD monitor and viewfinder video images
[HD/SD SDI OUT2] terminal output when [A/V Set] 
[SDI OUT2] is set to “VF”
[HDMI] terminal output when [A/V Set] [HDMI OUT] is set to “VF”
Memo
This item cannot be configured when [Color Space] is set to “J-Log1”.
The setting value of this item is stored separately when [Color Space] is set to “HLG”.
Color Gain
For adjusting the video signal color level. Increasing the value deepens the color.
[Setting Values: +15 to -50, Off ( 0)]
Memo
Images are displayed in black-and-white when this is set to “Off”.
This item cannot be configured when [Color Space] is set to “J-Log1”.
The setting value of this item is stored separately when [Color Space] is set to “HLG”.
Reverse Picture
For recording images correctly by setting this item to “Rotate” when the lens image appears upside down or laterally inverted.
Rotate:
Enables horizontal/vertical inversion of the image.
Off:
Disables horizontal/vertical inversion of the image.
[Setting Values: Rotate, Off]
DNR
Decreases noise in the image.
[Setting Values: High, Middle, Low]
Reset Process
Restores all items in the [Camera Process] menu to their default settings.
