> Connecting (Power On) > Pairing (Registering a device)
Pairing (Registering a device)
The method of operation varies depending on the connection.
Pairing for the First Time
-
1Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
Touch sensor area
-
After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
-
After a short while, both the L and R indicators start to flash quickly and repeatedly. You will hear an audio guidance indicating that the earphones are in the pairing mode.
For more information on the audio guidance, please click here. List of Audio Guidance
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
-
3Select “JVC HA-A7T2” from the device list.
-
JVC HA-A7T2
After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.
-
Touch sensor area
-
2Release your finger when both the L and R indicators start to flash quickly and repeatedly (or when you hear an audio guidance indicating that the earphones are in the pairing mode).
-
For more information on the audio guidance, please click here. List of Audio Guidance
When the indicators flash slowly, touch and hold the touch sensor areas for about 3 seconds to turn off the power. Touch and hold the touch sensor area until the indicators start to flash quickly again.
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
-
4Select “JVC HA-A7T2” from the device list.
-
JVC HA-A7T2
After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
Pairing the Second and Subsequent Devices
-
1Turn off the Bluetooth function of the device that was last paired.
-
2Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
Touch sensor area
-
After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
-
After a short while, both the L and R indicators start to flash quickly and repeatedly. You will hear an audio guidance indicating that the earphones are in the pairing mode.
For more information on the audio guidance, please click here. List of Audio Guidance
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
-
4Select “JVC HA-A7T2” from the device list.
-
JVC HA-A7T2
After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1Turn off the Bluetooth function of the device that was last paired.
-
2While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.
-
Touch sensor area
-
The indicator lights up for 1 second and the power turns on.
-
After a short while, both the L and R indicators start to flash quickly and repeatedly. You will hear an audio guidance indicating that the earphones are in the pairing mode.
For more information on the audio guidance, please click here. List of Audio Guidance
-
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
-
4Select “JVC HA-A7T2” from the device list.
-
JVC HA-A7T2
After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1Tap the touch sensor of either L (left) or R (right) earphone once, and touch and hold the touch sensor area for 3 seconds.
-
Touch sensor area
The L earphone is used in the illustration.
The earphones are disconnected from the device that was connected until then, and are on standby for the next pairing.
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
-
3Select “JVC HA-A7T2” from the device list.
-
JVC HA-A7T2
After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.
This operation is not possible during a call or hands-free calling.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.