Troubleshooting

Unable to pair

Place both earphones into the charging case, wait for the indicator light to turn off or turn red, followed by taking out the earphones again.

When pairing, make sure the BLUETOOTH device is within 1 m of the System.

Operate the BLUETOOTH device to connect.

Turn on the BLUETOOTH device and enable pairing.

Delete the pairing information on the BLUETOOTH device list and perform pairing again.

Perform operations after setting the BLUETOOTH function of the connected device to OFF and then to ON again.

Perform operations after turning off the connected device and on again.

Refer to the steps to establish a connection. Connecting (Power On)

Check whether the System is connected to another device. Turn off the BLUETOOTH settings of other devices and enable pairing with the desired device.

The L earphone flashes in red and connection cannot be established

Turn on the BLUETOOTH device, enable its Bluetooth function and select the System from the BLUETOOTH device list.

Sound is heard only from the left or right earphone

Place both earphones into the charging case, wait for the indicator light to turn off or turn red, followed by taking out the earphones again to establish a connection. After taking out the earphones, move the L and R earphones close to each other.

The L earphone is the master unit and is used to connect to a device as well as the R earphone. Insert the ear pieces more securely.

Reset the setting to factory default and connect again. Restoring the settings to the initial state

The R earphone flashes in red and no audio sound is output

Place both earphones into the charging case, wait for the indicator light to turn off or turn red, followed by taking out the earphones again to establish a connection. After taking out the earphones, move the L and R earphones close to each other.

After connecting to the System, the BLUETOOTH device connected does not function immediately

Depending on the device connected, even when the L indicator has turned white after connection is established, the earphones may not start functioning immediately due to a time lag in the connection. When this occurs, wait for a few seconds and repeat the operation.

The volume is low or the sound is unpleasant

Increase the volume on the System or the BLUETOOTH device connected.

Insert the ear pieces more securely.

Change the size of the ear pieces. Audio operation

Unable to skip back to the previous track

During playback, press and hold the button on the L earphone for about 1 second and release your finger when a beep is heard. The previous track or beginning of the current track will be played after the playback of the current track has ended.

Unable to skip to the next track

During playback, press and hold the button on the R earphone for about 1 second and release your finger when a beep is heard. The next track will be played after the playback of the current track has ended.

The earphones fall off the ears easily

Change the size of the ear pieces. Audio operation

The sound is distorted

Adjust the volume on the BLUETOOTH device connected so that there is no distortion, and then adjust the volume on the System.

Charge the main unit. Charging

Ring tone is soft and cannot be heard

The ring tone may not be heard from the earphone if the silent mode of the BLUETOOTH device is turned on. Turn off the silent mode of the BLUETOOTH device or adjust the volume of the ring tone.

The sound is choppy and there is noise

Use the connected device in a position or orientation that allows for the most stable communication. The sound tends to be interrupted when the earphones are covered with the hands. The L earphone is the master unit and is used to connect to a device as well as the R earphone.

Try reducing the number of apps running on the BLUETOOTH device connected.

Charge the main unit. Charging

The System does not work correctly

Re-charge the system and switch power on.

Unable to turn on the power

Charge the charging case first. Charging the charging case

Charge the main unit. Charging

Unable to charge and turn off the power
(earphones)

Remove both earphones from the charging case and place them back in again.

Make sure that the earphones are fully inserted into the charging case.

Use a cotton swab to remove any dirt from the contacts of the earphones and charging case.

Charge the charging case first. Charging the charging case

Unable to charge
(charging case)

Make sure that the USB cable is plugged in all the way.

Please charge within the charging temperature range (5 °C (41 °F) to 40 °C (104 °F)).

The earphones are turned on during charging

When the charging case runs out of battery, the earphones are turned on. In this case, turn the earphones off manually. Powering off using the earphones

Charge the charging case. Charging the charging case

Unsure what the flashing and lighting up of the indicators indicate

Refer to Indicator status list.

Music or voice calls cannot be heard

Delete the pairing information on the BLUETOOTH device list. Perform pairing after turning off the connected device and on again (or after rebooting).