DIRECT MONITORING

Setting (Once setting is done, start from the “Regular Operation” below)

1Create a QR code.

Enter values in the required items for direct monitoring.

Password: set a password to connect this camera to the device by direct monitoring. (8 to 63 characters (64 characters in case of hexadecimal))

Enforced Group Owner: setting used to enable a connection with a device that does not support Wi-Fi Direct. Normally set to “ON”.

HTTP Port: Normally set to “80”.

Input Form

Password (no value if no change is made)

Enforced Group Owner
HTTP Port (0 to 65535)

2Display the screen for reading the QR code.

Tap “MENU”.
(Operation on this camera)

Tap MENU

The top menu appears.

Tap the “Wi-Fi” ( Wi-Fi ) icon.
(Operation on this camera)

C3B_TOP_MENU(Wi-Fi)

Tap Cursor_Right on the lower right of the screen.
(Operation on this camera)

C3-Wi-Fi_MENU_1

Tap “COMMON Wi-Fi SETTING”.
(Operation on this camera)

C3-Wi-Fi_MENU_2

Tap “SET FROM QR CODE”.

C3_WiFi_COMMON-SET_QRCORD

Tap “EXECUTE”.

C3_WiFi_QR_CORD_SET_USERGUIDE

3Read a QR code.

Read a QR code.
(Operation on this camera)

C3_WiFi_COMMON-SET_READ_QRCORD

Tap “YES”.

C3_WiFi QR_CORD DIRECT OVERWRITTEN

Tap “OK”.

C3_WiFi_QR_CORD_SETTING_DONE

Tap “NEXT” to return to the screen to read the QR code.

Set contents are saved.

Regular Operation

4Connecting the Smartphone to the Camera Wirelessly

Connection by entering the Wi-Fi password

Tap “MENU”.
(Operation on this camera)

Set the camera to the recording mode.

Tap MENU

The top menu appears.

Tap the “Wi-Fi” ( Wi-Fi ) icon.
(Operation on this camera)

C3B_TOP_MENU(Wi-Fi)

Tap the “DIRECT MONITORING” ( D-MONITOR ) icon in the “Wi-Fi” menu.
(Operation on this camera)

C3-Wi-Fi_MENU_1

Tap “START” ( C2_Stamp-Arrow ).
(Operation on this camera)

C3_WiFi_D-MONITOR

When iFrame is selected for “VIDEO REC FORMAT”, the following display appears and recording mode is switched to the 50i mode in AVCHD.

This display disappears automatically after approximately 3 seconds, but disappears immediately if the screen is tapped.

C3 WiFi D-MONITOR2 Euro

Check the SSID and the PASS being displayed on the screen of the camera.

C2-WiFi_DIRECT MONITORING2-2

Select the SSID in step 5 from the Wi-Fi network selection screen of your smartphone, and enter the PASS on the password screen.
(Operation on the smartphone (or computer))

Smartphone

For details on connecting your smartphone (or computer) to a Wi-Fi network, please refer to the instruction manual of the phone terminal in use.

A connection is established and Wi-Fi appears on the camera’s screen.

C3-Wi-Fi_Screen_Wi-Fi

Connection by Wi-Fi Protected Setup (WPS)

Tap “MENU”.
(Operation on this camera)

Set the camera to the recording mode.

Tap MENU

The top menu appears.

Tap the “Wi-Fi” ( Wi-Fi ) icon.
(Operation on this camera)

C3B_TOP_MENU(Wi-Fi)

Tap the “DIRECT MONITORING” ( D-MONITOR ) icon in the “Wi-Fi” menu.
(Operation on this camera)

C3-Wi-Fi_MENU_1

Tap “START” ( C2_Stamp-Arrow ).
(Operation on this camera)

C3_WiFi_D-MONITOR

When iFrame is selected for “VIDEO REC FORMAT”, the following display appears and recording mode is switched to the 50i mode in AVCHD.

This display disappears automatically after approximately 3 seconds, but disappears immediately if the screen is tapped.

C3 WiFi D-MONITOR2 Euro

Tap “WPS”.
(Operation on this camera)

C2-WiFi_DIRECT MONITORING2-2

Activate WPS on the smartphone (or computer) within 2 minutes.
(Operation on the smartphone (or computer))

Smartphone

To activate WPS, refer to the instruction manual of the device in use.

A connection is established and Wi-Fi appears on the camera’s screen.

C3-Wi-Fi_Screen_Wi-Fi

5Monitoring the Images from a Smartphone (or Computer)

Smartphone (Android / iPhone)

Memo

Prior to use this function, a smartphone application needs to be installed on the smartphone.

Start “Everio sync. 2” on the smartphone after setting DIRECT MONITORING.

Smartphone

Tap “DIRECT MONITORING”.

Everio Sync.2-1

The recording screen is displayed.

Appli Android Top1

Operate from a smartphone

Smartphone ope

How to operate from a smartphone

Computer (Windows 7)

Tap the URL button shown on the camera’s screen.
(displayed when the computer and the camera are connected wirelessly.)

C3-Wi-Fi_Screen_Wi-Fi

The URL for the computer to connect to appears.

Check the URL displayed on the camera screen, which starts from “http://”.

C3_WiFi_NETWORK_INFO

After checking the URL, tap “QUIT” to return to the previous screen.

Start Internet Explorer (web browser) on the computer and enter the URL.

Internet explorer