User Switch Set Item

USER0 to USER8, USER9 , USER10 , USER11 , USER12 , USER13 (front), USER1 (VF), USER2 (VF), LENS RET

The preconfigured function can be operated (on/off, start, switch) by assigning one of the functions in the following menu table to [USER0], [USER1], [USER2], [USER3], [USER4], [ONLINE/5], [USER6], [USER7], [USER8], [ /9], [ /10], [ /11], [ /12], front [SET/USER13] button, [RET] button on the lens and the [USER1(VF)] and [USER2(VF)] buttons on the viewfinder.
Set according to the shooting conditions. Usable in the Camera mode.

Assignment of Functions to User Buttons

Memo

When a viewfinder is connected, priority is given to the [ZEBRA] switch of the viewfinder and the user button that is assigned with the “Zebra” function will not function.

“Focus Assist +” is a combination of the “Focus Assist” and “Expanded Focus” functions.

“Skin Detail +” is a combination of the “Skin Detail” and “Skin Area” functions.

The [SET/USER13] button at the front functions as the [STATUS/SET] button in the factory setting, but it can also be assigned with the [USER13] function.

If “VF Display” is assigned to the [USER1(VF)] or [USER2(VF)] button of the viewfinder, the button can also be used in the Media mode.

The following functions can be assigned only for 900CHU 900STU .
[ODK Tagging]OFF, [ODK Tagging]DEF, [ODK Tagging]KO, [ODK Tagging]KOR, [ODK Tagging]P, [ODK Tagging]PR, [ODK Tagging]FG, [ODK Tagging]FGB, [ODK Tagging]REMOVE

The settable values for each item are as follows.

Button Setting Value	[8]	[5]/[6]/[7]/ [LENS RET]	[0]/[1]/ [3]/[4]/ [9]/[10]/ [11]/[12]/ [13]	[2]	[USER1(VF)]/ [USER2(VF)]
VF Display
Cancel
Status
Slot Select
Auto Upload
Return over IP
Live Streaming
Load Picture File
Return Video
Clip Review
OK Mark
Clip Cutter Trig
Backup Trig
Rec
LCD Backlight
Spot Meter
Focus Assist
Expanded Focus
Focus Assist +
Marker
Zebra
Video Signal Monitor
AWB
White Balance
Black Compress
Black Stretch
Skin Detail
Skin Area
Skin Detail +
Zoom Wide
Zoom Tele
FULL AUTO
AE Level
AE Lock
Variable Gain
Lolux
None

Settable

Not settable

Lolux

To increase the sensitivity when in dim surroundings, set a value in the Lolux mode.

When [LCD/VF] [Display Type] [Gain] is set to “dB”:
[Setting Values: 42 dB, 36 dB, 30 dB, 24 dB]

When [LCD/VF] [Display Type] [Gain] is set to “ISO”:
[Setting Values: ISO 102400, ISO 51200, ISO 25600, ISO 12800]

Clip Review

For configuring the behavior when operating the user button that is assigned with the “Clip Review” function.

Last 5sec:
Views about 5 seconds of the clip from the ending.

Top 5sec:
Views about 5 seconds of the clip from the beginning.

Clip:
Views the entire clip.

[Setting Values: Last 5sec, Top 5sec, Clip]

Spot Meter

For configuring the behavior when operating the user button that is assigned with the “Spot Meter” function.

Max & Min:
Displays the brightest and darkest areas of the image.

Max:
Displays the brightest area of the image.

Min:
Displays the darkest area of the image.

Manual:
Displays the image brightness at a specified position.

[Setting Values: Max & Min, Max, Min, Manual]

Memo

When “HLG” is selected in [Camera Process] arrowR [Color Space], the value of the spot meter changes according to the setting of [LCD/VF] arrowR [Convert to ITU709]/[White Level].

AE Lock

For configuring the behavior when operating the user button that is assigned with the “AE Lock” function.

FAW:
Use this to fix the FAW (Full-time Auto White Balance) function to the value when the user button assigned with “AE Lock” is pressed.

AE:
Use this to fix the Auto function of Gain, Iris, or Shutter to the value when the user button assigned with “AE Lock” is pressed.

AE/FAW:
Use this to fix the FAW (Full-time Auto White Balance) function and the Auto function of Gain, Iris, or Shutter to the value when the user button assigned with “AE Lock” is pressed.

[Setting Values: FAW, AE, AE/FAW]

Memo

This feature only works when Iris, Shutter, Gain or White Balance is set to Auto mode.

“AE Lock” is canceled when the user button assigned with “AE Lock” is pressed, or when any of the functions that can be locked is operated regardless of the mode (Manual or Auto).

“AE Lock” is canceled when the lens extender is operated and when the iris is adjusted by 2/3 (two-third) stop or more.

“AE Lock” is canceled in the following cases.

When the user button that is assigned with “AE Lock” is pressed

When changes are made to the iris (including operation of the lens extender), gain and shutter settings

When changes are made to the AE level

When there is a switch between the Camera and Media modes

Zoom Speed

For configuring the zoom speed when operating the user button that is assigned with “Zoom Tele” or “Zoom Wide”.
Increasing the value increases the speed.

[Setting Values: 8 to 5 to 1]

Expanded Focus

For configuring the behavior when operating the user button that is assigned with the “Expanded Focus” function.

Limited Time:
Activates the timer.
Turns off the “Expanded Focus” function about 3 seconds after the user button assigned with “Expanded Focus” is pressed.

Momentary:
The “Expanded Focus” function is enabled during the interval while the user button assigned with “Expanded Focus” is pressed.

Toggle:
Pressing the user button assigned with “Expanded Focus” each time switches the “Expanded Focus” function to on or off.

[Setting Values: Limited Time, Momentary, Toggle]

Memo

When “Toggle” is selected after assigning the expanded focus to any of the [ U_botton /9], [ D_botton /10], [ L_botton /11], [ R_botton /12] buttons, press the [CANCEL/RESET] button if you want to disable the function.

Video Signal Monitor

For configuring the behavior when operating the user button that is assigned with the “Video Signal Monitor” function.

Switch in Order:
Pressing the button each time switches the mode in the following sequence: Vectorscope, Waveform, Histogram, Off.

On/Off:
Switches the function configured in [LCD/VF] [Shooting Assist] [Video Signal Monitor] to on or off.

[Setting Values: Switch in Order, On/Off]

Return Video

For configuring the behavior when operating the user button that is assigned with the “Return Video” function.

Camera PiP:
Pressing the user button assigned with the “Return Video” function each time toggles between the captured video and picture-in-picture return video.

Camera PiP:
The picture-in-picture return video is displayed when the user button assigned with the “Return Video” function is pressed and held down, and the captured video is displayed when the button is released.

PiP Camera:
The captured video is displayed when the user button assigned with the “Return Video” function is pressed and held down, and the picture-in-picture return video is displayed when the button is released.

PiP Return:
The return video is displayed when the user button assigned with the “Return Video” function is pressed and held down, and the picture-in-picture return video is displayed when the button is released.

Camera Return:
The return video is displayed when the user button assigned with the “Return Video” function is pressed and held down, and the captured video is displayed when the button is released.

[Setting Values: Camera PiP, Camera PiP, PiP Camera, PiP Return, Camera Return]