> Connecting (Power On) > Pairing (Registering a device)
Pairing (Registering a device)
The method of operation varies depending on the connection.
Pairing for the First Time
-
1Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
-
After the earphones are taken out, the L (left) and R (right) indicators flash, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash every 5 seconds.
-
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
Either the L or R earphone will be the base unit connecting to the BLUETOOTH device and the other earphone.
-
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
3Select “JVC HA-A50T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
-
1While the power is turned off, touch and hold the touch sensor area of both L (left) and R (right) earphones for about 3 seconds.
-
2The power of the L and R earphones turns on. When the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your fingers from the buttons.
-
When the L indicator flashes slowly, touch and hold the touch sensor area for about 3 seconds to turn off the power. Touch and hold the touch sensor area until the indicator starts to flash quickly again.
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “JVC HA-A50T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
Pairing the Second and Subsequent Devices
-
1Turn off the Bluetooth function of the device that was last paired.
-
2Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
-
After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash every 5 seconds.
-
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “JVC HA-A50T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the System automatically turns itself off.
-
1Turn off the Bluetooth function of the device that was last paired.
-
2While the power is turned off, touch and hold the touch sensor area of the L (left) earphone for about 5 seconds.
-
Pressing and holding the touch sensor area on the L earphone for about 10 seconds while it is in the charging case initializes the pairing (device registration) information. In this case, perform pairing (device registration) again.
Pressing and holding the touch sensor area on the L earphone for about 20 seconds while it is in the charging case initializes the pairing (device registration) information and deletes the connection information for the L and R earphones. When this occurs, reset the earphones to the factory default state. Restoring the settings to the initial state -
3When the power of the L earphone turns on and the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your finger from the button.
-
4Turn on the Bluetooth function of the BLUETOOTH device.
-
5Select “JVC HA-A50T” from the device list.
-
When the L earphone is successfully connected to the device, the L indicator starts to flash every 5 seconds.
-
6Touch and hold the R (right) touch sensor area for about 3 seconds. Release your finger after the R indicator lights up. The R earphone turns on and gets connected to the L earphone.
-
After connection is established, the R indicator will flash every 5 seconds, and the earphones can now be used for listening to music.
Pressing and holding the touch sensor area on the R earphone for about 10 seconds while it is in the charging case initializes the pairing (device registration) information. In this case, perform pairing (device registration) again.
Pressing and holding the touch sensor area on the R earphone for about 20 seconds while it is in the charging case initializes the pairing (device registration) information and deletes the connection information for the L and R earphones. When this occurs, reset the earphones to the factory default state. Restoring the settings to the initial state