> Connecting (Power On) > Pairing (Registering a device)

Pairing (Registering a device)

The method of operation varies depending on the connection.

Pairing for the First Time

1Take out both the L (left) and R (right) earphones.

Be careful not to touch the touch sensor area when taking them out.

Case_button_A6T + Case_button_A6T

Touch sensor area

  1. After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.

  2. When the L and R earphones are connected, the R indicator will flash slowly and repeatedly twice.

  3. After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.

  4. connecting_0.3_2_A6T

When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.

2Turn on the Bluetooth function of the BLUETOOTH device.

connecting 2 New

3Select “JVC HA-A6T” from the device list.

connecting 3 Cap + Device List JVC

JVC HA-A6T

After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.

blue_flash_A6T

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

1While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.

PLAY_button_LR_A6T + Button_LR_A6T

Touch sensor area

2When the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your fingers from the touch sensor.

connecting_0.3_2_A6T

When the indicators flash slowly, touch and hold the touch sensor areas for about 3 seconds to turn off the power. Touch and hold the touch sensor area until the indicators start to flash quickly again.

3Turn on the Bluetooth function of the BLUETOOTH device.

connecting 2 New

4Select “JVC HA-A6T” from the device list.

connecting 3 Cap + Device List JVC

JVC HA-A6T

After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.

blue_flash_A6T

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

Pairing the Second and Subsequent Devices

1Turn off the Bluetooth function of the device that was last paired.

2Take out both the L (left) and R (right) earphones.

Be careful not to touch the touch sensor area when taking them out.

Case_button_A6T + Case_button_A6T

Touch sensor area

  1. After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.

  2. When the L and R earphones are connected, the R indicator will flash slowly and repeatedly twice.

  3. After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.

  4. connecting_0.3_2_A6T

When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.

3Turn on the Bluetooth function of the BLUETOOTH device.

connecting 2 New

4Select “JVC HA-A6T” from the device list.

connecting 3 Cap + Device List JVC

JVC HA-A6T

After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.

blue_flash_A6T

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

1Turn off the Bluetooth function of the device that was last paired.

2While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.

PLAY_button_LR_A6T + Button_LR_A6T

Touch sensor area

  1. The indicator lights up for 1 second and the power turns on.

  2. After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.

  3. connecting_0.3_2_A6T

3Turn on the Bluetooth function of the BLUETOOTH device.

connecting 2 New

4Select “JVC HA-A6T” from the device list.

connecting 3 Cap + Device List JVC

JVC HA-A6T

After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.

blue_flash_A6T

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

1Tap the touch sensor of either L (left) or R (right) earphone once, and touch and hold the touch sensor area for 3 seconds.

PLAY_button_L_A6T + Button_L_A6T

Touch sensor area

The L earphone is used in the illustration.

The earphones are disconnected from the device that was connected until then, and are on standby for the next pairing.

2Turn on the Bluetooth function of the BLUETOOTH device.

connecting 2 New

3Select “JVC HA-A6T” from the device list.

connecting 3 Cap + Device List JVC

JVC HA-A6T

After connection is established, both the L and R indicators will flash slowly, and the earphones can now be used for listening to music.

blue_flash_A6T

This operation is not possible during a call or hands-free calling.

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.