> Connecting (Power On) > Pairing (Registering a device)
Pairing (Registering a device)
The method of operation varies depending on the connection.
Pairing for the First Time
-
1Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
-
After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash twice every 5 seconds.
-
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
3Select “JVC HA-A4T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.
-
2When the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your fingers from the touch sensor.
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “JVC HA-A4T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
Pairing the Second and Subsequent Devices
-
1Turn off the Bluetooth function of the device that was last paired.
-
2Take out both the L (left) and R (right) earphones.
-
Be careful not to touch the touch sensor area when taking them out.
-
After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
-
When the L and R earphones are connected with each other, the R indicator starts to flash twice every 5 seconds repeatedly.
-
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.
When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.
-
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “JVC HA-A4T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1Turn off the Bluetooth function of the device that was last paired.
-
2While the power is turned off (both L and R indicator lights are off), tap and hold the touch sensor on both the L (left) and R (right) earphones for about 3 seconds. The power of the L and R earphones turns on.
-
-
The indicator lights up for 1 second and the power turns on.
-
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.
-
-
3Turn on the Bluetooth function of the BLUETOOTH device.
-
4Select “JVC HA-A4T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.
-
1Tap the touch sensor of either L (left) or R (right) earphone once, and touch and hold the touch sensor area for 3 seconds.
-
The L earphone is used in the illustration.
The earphones are disconnected from the device that was connected until then, and are on standby for the next pairing.
-
2Turn on the Bluetooth function of the BLUETOOTH device.
-
3Select “JVC HA-A4T” from the device list.
-
After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.
This operation is not possible during a call or hands-free calling.
During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.
If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.