> Connecting (Power On) > Pairing (Registering a device)

Pairing (Registering a device)

The method of operation varies depending on the connection.

Pairing for the First Time

Pairing with the earphones taken out from the charging case

1Take out both the L (left) and R (right) earphones.

After the earphones are taken out, the L (left) and R (right) indicators flash, and the power turns on automatically.
When the L and R earphones are connected with each other, the R indicator starts to flash every 5 seconds.
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.

When there is an interval between the timing when the L and R earphones are taken out from the charging case, connection between them may fail. In this case, put the earphones back into the charging case, wait till their power goes off and repeat the steps again.

2Turn on the Bluetooth function of the BLUETOOTH device.

3Select “JVC HA-A7T” from the device list.

JVC HA-A7T

After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

Pairing earphones when they are not inside the charging case

1Press and hold the button on the L (left) and R (right) earphones for about 3 seconds.
2The power of the L and R earphones turns on. When the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your fingers from the buttons.: If the L indicator does not flash quickly, turn off the power of the earphones and repeat the steps. Power Off
3Turn on the Bluetooth function of the BLUETOOTH device.
4Select “JVC HA-A7T” from the device list.: JVC HA-A7T

After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

Pairing the Second and Subsequent Devices

Pairing with the earphones taken out from the charging case

1Turn off the Bluetooth function of the device that was last paired.

2Take out both the L (left) and R (right) earphones.

After the earphones are taken out, the L and R indicators will flash, and the power turns on automatically.
When the L and R earphones are connected with each other, the R indicator starts to flash every 5 seconds.
After a short while, the L indicator starts to flash quickly and repeatedly, and a voice message saying “Pairing” can be heard.

3Turn on the Bluetooth function of the BLUETOOTH device.

4Select “JVC HA-A7T” from the device list.

JVC HA-A7T

After connection is established, both the L and R indicators will flash every 5 seconds, and the earphones can now be used for listening to music.

During the pairing process, the BLUETOOTH device may require input of a PIN code. In such a case, enter “0000” as the PIN code for the System.

If connection (pairing) is not completed within 5 minutes after the indicator starts flashing, the earphone automatically turns itself off.

Pairing earphones when they are not inside the charging case

1Turn off the Bluetooth function of the device that was last paired.
2With the power of the earphones turned off, press and hold the button on the L (left) earphone for about 5 seconds.
3When the power of the L earphone turns on and the L indicator starts to flash quickly and repeatedly (or when a voice message saying “Pairing” is heard), release your finger from the button.
4Turn on the Bluetooth function of the BLUETOOTH device.
5Select “JVC HA-A7T” from the device list.: JVC HA-A7T

When the L earphone is successfully connected to the device, the L indicator starts to flash every 5 seconds.
6Press and hold the button on the R (right) earphone for about 3 seconds. Release your finger after the R indicator lights up. The R earphone turns on and gets connected to the L earphone.: After connection is established, the R indicator will flash every 5 seconds, and the earphones can now be used for listening to music.