[PTZ] Page

TOP

This page allows you to specify the Move Preset Position and Auto Flip settings.

This page can be used during access using“admin” or “operator”.

Click [Advanced Settings]in the side menu, and click [PTZ].

Press the [OK]button to enable the new settings.

If the [OK]button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel]button to restore the invalid entry to the value before the change was made. If you press the [Cancel]button, other changed items will also be restored to the values before the change was made.

Settings

Setting values with circle_B are default values.

EZoom Limit

When the zoom lens is operated to TELE side, optical zoom works and electronic zoom works after optical zoom becomes full. This item sets the maximum value of the electronic zoom function.

[Set values: 1, 2, 4, 8, 10]

Memo

As electronic zoom processes the images digitally, image quality will deteriorate slightly

Increasing the electronic zoom ratio will shift the center of the screen toward the top left. This is a characteristic of this camera and is not a malfunction.

During continuous zoom operation, there is a one-second pause when the electronic zoom switches to optical zoom. This is intended to mark the boundary between electronic and optical zoom, and is not a malfunction.

Pan Limit

This item sets the movable range of the pan (horizontal) operation during manual operation when “ON” is selected. It is invalid when “OFF” is selected.

[Set values: ON, OFF]

[Set Left], [Set Right]:
Click these buttons to set the current position to the left or right edge.

[Go to Left], [Go to Right]:
Click these buttons to move the camera to the preset left or right edge.

Memo

This item does not affect the preset position and auto pan operation.

Basic operation of Pan Limit

When [Pan Limit]is set to “ON”, panning is only available in the effective area.
When the camera is moved to prohibited area by some operation that has priority over [Pan Limit] and manual panning is performed, it operates in the following manner.

Memo

Panning can be operated freely even in the prohibited area before the camera enters the effective area.

Once the camera enters the effective area, the [Pan Limit]settings take over and pan operation can only be performed in the effective area.

Operations that have priority over Pan Limit

The following operations are available regardless of the prohibited areas set in [Pan Limit].

Auto Pan

Move Preset Position

Auto Flip

Settings that have priority over Pan Limit

The following setting comes together with pan operation but they can be set regardless of the prohibited areas even when [Pan Limit]is set to “ON”.

Auto Pan setting

Memo

When setting Preset Position with [Pan Limit]set to “ON”, panning operation is disabled in the prohibited area.

As Move Preset Position has priority over manual pan limit, setting the manual pan limit after setting Preset Position does not prevent Preset Position operation in the prohibited area.

Tilt Limit

This item sets the movable range of the tilt (vertical) operation during manual operation.
When this item is set to 10°, the movable range of the tilt operation is from 10° to 90°. It cannot operate between -5° and 9°.
When the[Auto Flip]item is set to “Digital Flip”, Tilt Limit is set for the tilt operation to 180°.

[Set values: -5 Degree to 0 Degree to 10 Degree]

Memo

When the camera is moved to the prohibited area by some operation that gives priority to Tilt Limit and manual tilt operation is performed, it operates in the following manner.

Tilt operation is disabled in the prohibited area. Tilt will be forcibly moved to the effective area.

Once the camera enters the effective area, the Tilt Limit settings take over and tilt operation can only be performed in the effective area.

This item does not affect the preset position and auto pan operation.

Auto Flip

Set this item when shooting objects that pass right under the camera.
Otherwise, following operations are necessary to shoot objects that pass right under the camera.

Turn the camera to face down

Rotate the camera 180° horizontally

Turn the camera to face up

You can use the [Auto Flip]function to perform the above operations automatically.

OFF:
Auto Flip function does not activate.

Digital Flip:
The top/bottom and left/right of the image flips when tilt position passed the angle of 135°.

Mode1:
When the camera faces bottom, it rotates 180° horizontally and stops. In this case, the operating direction of the camera is the same as that of the Pan/Tilt operation.

Mode2:
When the camera faces down, it rotates 180° horizontally and the camera operates in a direction opposite to that of the Tilt operation. Select this mode if you wish to operate continuously. Once operation stops, the direction will return to normal.

Mode3:
When the camera faces bottom, it rotates 180° horizontally and the operating direction of the camera is opposite that of the Tilt operation. However, the operating direction will return to normal 10 seconds after the operation has stopped.

[Set values: OFF, Digital Flip, Mode1, Mode2, Mode3]

Memo

Settings for [Preset Position Speed]are reflected in [Speed]when images are flipped using “Mode1”, “Mode2”, “Mode3”. To flip images in high speed using “Mode1”, “Mode2”, “Mode3”, set the [Preset Position Speed] in [Speed] to “High”.

Note

When [Auto Flip]is set to other than “OFF”, the camera can be moved to areas outside the pan limit with the Tilt operation. When “Digital Flip” is set, use the Tilt operation to flip and return to the pan limit area again. When “Mode1”, “Mode2” or “Mode3” is set and the camera is moved to inside of the pan limit with Pan operation, it will stop at the pan limit position.