By obtaining a dynamic DNS account, this unit may be used on the web as usual even if the IP address changes when making an access to this unit via internet.
-
- Using Wi-Fi by Creating a QR Code
-
OUTDOOR MONITORING
OUTDOOR MONITORING
Setting (Once setting is done, start from the “Regular Operation” below)
1Obtaining a Dynamic DNS (DDNS) Account
Only the JVC dynamic DNS service can be set on this camera.
To obtain (register) an account, perform the following steps.
Caution
Registration will be canceled if you do not access the dynamic DNS server from the camera within 3 days.
Perform the registration again in this case.
Registration will not be complete if the username and password set on this camera are incorrect. Be sure to check that they are correct.
Successful registration will be canceled too if you do not access the dynamic DNS server for 1 year.
2Creating a QR Code
Enter values in the required items for outdoor monitoring.
All items will be overwritten and set. Enter all the required items.
If connection fails, check that the contents entered for each item are correct, regenerate the QR code and set the camera.
Password: set a password to connect this camera to the device via an access point. (Not more than 8 characters)
DDNS: Set the connection environment to the internet. Normally set to “ON”.
User name (DDNS): set an user name for the obtained DDNS account.
Password (DDNS): set a password for the obtained DDNS account.
UPnP: Set to “ON” if the UPnP protocol may be used to connect the device to the network.
HTTP Port: Set the port number for connecting to the internet. Normally set to “80”.
3Display the screen for reading the QR code.
Tap “MENU”.
(Operation on this camera)
The top menu appears.
Tap the “Wi-Fi” ( 
) icon.
(Operation on this camera)
_UJDCILympypskr.png)
Tap “Wi-Fi SETTING”.
(Operation on this camera)
Tap “SET FROM QR CODE”.
Tap “EXECUTE”.
4Read a QR code.
Read a QR code.
(Operation on this camera)
Tap “YES”.
Tap “OK”.
Tap “NEXT” to return to the screen to read the QR code.
Set contents are saved.
5Registering the access points (wireless LAN router) to this unit
Wi-Fi Protected Setup (WPS) Registration
Tap “MENU”.
(Operation on this camera)
The top menu appears.
Tap the “Wi-Fi” ( ) icon.
(Operation on this camera)
Tap “Wi-Fi SETTING”.
(Operation on this camera)
Tap “ACCESS POINTS”.
(Operation on this camera)
Tap “ADD”.
(Operation on this camera)
Tap “EZ REGISTRATION WPS”.
(Operation on this camera)
Activate WPS of the access point (wireless LAN router) within 2 minutes.
To activate WPS, refer to the instruction manual of the device in use.
After registration is complete, tap “OK” on the camera’s screen.
(Operation on this camera)
The following registration methods are also available.
Regular Operation
6Connecting the Camera to the Smartphone
Tap “MENU”.
(Operation on this camera)
The top menu appears.
Tap the “Wi-Fi” ( ) icon.
(Operation on this camera)
Tap “ACCESS POINT CONNECTION”.
(Operation on this camera)
Start making a connection.
(Operation on this camera)
Name (SSID) of the access point (wireless LAN router) in connection is displayed.
The following is displayed when the camera is connected to the access point.
Tapping “INFO.” displays the URL (WAN) for connecting the smartphone.
(Does not appear if DDNS is not set or set incorrectly.)
“ 
UPnP” is displayed when UPnP cannot be used.
Operation on the smartphone
Memo
Prior to use this function, a smartphone application needs to be installed on the smartphone.
Start “Everio sync. 3” on the smartphone after setting OUTDOOR MONITORING.
Tap “START” in OUTDOOR MONITORING on the camera to start.
Tap “OUTDOOR MONITORING”.
Set the URL.
It is necessary to set the URL when you are using this feature for the first time. Enter the URL displayed on the camera.
If this screen is displayed after the URL has been set, check the connection status of the internet or the camera settings.
Log in with your username and password.
(if authentication cannot be achieved)
The username is “everio” and the default password is “0000”.
To change the password, it is necessary to generate a QR code.
The recording screen is displayed.
