[FTP Recording] Page

TOP

This page describes setting procedures related to recording.

This page can be used during access using “admin” or “operator”.

Click [Advanced Settings] in the side menu, and click [Record Status].

Press the [OK] button to enable the new settings.

If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel] button to restore the invalid entry to the value before the change was made. If you press the [Cancel] button, other changed items will also be restored to the values before the change was made.

Options displayed vary according to the recording mode selected.

Settings

Setting values with circle_B are default values.

Record Status

For selecting a recording mode. Selecting “ON” displays options after [Record Status].

[Set values: ON, OFF]

FTP Server

For setting the IP address or FQDN of the FTP server.

Path

For setting the path name. When [Path] is left blank, FTP transfer will be performed to the home directory of the FTP server.

Memo

To enable FTP transfer to a directory below the home directory, set the corresponding directory name in [Path]. Delimit the directory using “/”.
Example: subdir1/subdir2

Destination directory of FTP transfer will be dependent on the FTP server if “/” is added at the beginning.

User Name

Enter the user name.

Password

Enter a password. When a user name is specified, “******” is displayed.

Recording Mode

For setting the FTP recording mode. Options for [Constant] vary according to the selected [Recording Mode].

Constant:
Transfers JPEG images to the FTP server constantly at the preset time.

Alarm:
Transfers JPEG images before and after the occurrence of an alarm that matches the preset conditions to the FTP server.

Constant+Alarm:
Enables both Constant and Alarm recording.

[Set values: Constant, Alarm, Constant + Alarm]

Constant

Settings for performing constant recording.

Encoder

For selecting the encoder for performing constant recording.

Memo

You can select a JPEG encoder number.

Interval

For setting the recording interval in seconds.

[Set values: 1 to 65535] seconds

File Naming

Three types of recording file names are available for selection.

“Auto”:
Generated from the year/month/day/hour/minute/second, and number.
Example: 20121114161032-001-2.jpg

“Manual1”:
Year, month, day, hour, minute, second, and number are added to [User-Defined-String] in the file name.
Example: Camera1_20121114161032001.jpg

“Manual2”:
File name contains only the character string entered in [User-Defined-String]
Example: Camera1.jpg

[Set values: Auto, Manual1, Manual2]

Sunday to Saturday

For selecting whether to activate or stop recording by day of the week.

[Set values: Unmask All, Mask All, Unmask Span, Mask Span]

For setting the time period when “Unmask Span” or “Mask Span” is selected.

[Set values: 00H00M to 24H00M]

Alarm

Settings for performing alarm recording.

Encoder

For setting the encoder for performing alarm recording, and the JPEG frame rate.

[Set values: 30 fps, 15 fps, 10 fps, 7.5 fps, 5 fps, 3 fps, 2 fps, 1 fps]

Memo

You can select a JPEG encoder number.

The settable frame rate varies with the encoder setting.

Trigger1, Interval, Trigger2

Trigger1:
Select the 1st trigger to perform an action.
[Set values: Pin Input1 Make, Pin Input2 Make, Pin Input1 Break, Pin Input2 Break, Position, Motion Detection, Tampering Detection, Time, FAN Stop]

Interval:
Specify the maximum interval between each trigger for [Trigger1] and [Trigger2].
[Set values: 1 to 3600]

Trigger2:
Select the 2nd trigger to perform an action.
[Set values: Disable, Pin Input1 Make, Pin Input1 Break, Pin Input2 Make, Pin Input2 Break]

Position Number

Displayed when “Position” is selected in [Trigger1]. Executes an action upon moving to the entered preset position.

[Set values: 0 to 99]

Memo

Specify the setting for Preset Position in [PTZ Settings] of Built-in Viewer.

[PTZ Settings]

Time

Displayed when “Time” is selected in [Trigger1]. Executes an action at the time you have entered.

[Set values: 00H00M to 23H59M]

Pre-Trigger

For setting the FTP pre-recording trigger time (recording time before alarm input) in seconds.

[Set values: 0 to 5 to 60]sec

Post-Trigger

For setting the FTP post-recording trigger time (recording time after alarm input) in seconds.

[Set values: 0 to 5 to 60]sec

Sunday to Saturday

For selecting whether to activate or stop recording by day of the week.

[Set values: Unmask All, Mask All, Unmask Span, Mask Span]

For setting the time period when “Unmask Span” or “Mask Span” is selected.

[Set values: 00H00M to 24H00M]