[PTZ Settings]

TOP

This item sets the PTZ functions.

This page can be used during access using “admin” or “operator”.

While another menu is open, click [Control] to switch to the Control Menu. Click [PTZ Settings] to open the Settings screen.

Preset Position

Sets the camera preset position.

Point the lens in the shooting direction using the pan, tilt, or zoom operation. Select a position number, followed by inputting a position title. Next, click [Register] to register the position. The position number is used for alarm trigger, moving to a specific position, and the position settings of Auto Patrol.

When [Auto Flip] is set to “Digital Flip”, preset positions cannot be registered when the tilt angle is more than 90 degrees.

Auto Flip

Memo

This product enables setting up to 100 preset positions, including HOME and 1 to 99.

When setting preset positions and [Pan Limit] is “ON”, pan operation is unavailable in the prohibited areas.

As moving preset positions has priority over pan limit, set the preset positions when [Pan Limit] is “OFF”. After that, when [Pan Limit] is set to “ON”, the camera will pan regardless of the prohibited areas.

Items that are stored in the preset position include pan, tilt, zoom, focus, position title, white balance, iris, and backlight compensation.

Position

Selects a Position.

[Set values: HOME, 1 to 99]

Title

Displays the current title.

[Title]:
To register or change the title, enter a title here.
(You can input up to 32 characters. However, the JPEG Viewer only supports display up to 16 characters.)

[Register] button:
Click to complete registration of the new position.

[Unregister] button:
Click to delete information on the selected position.

Memo

Note that you cannot delete the [HOME] position.

Auto Pan

Specifies the auto pan settings. This item sets the Auto Pan operation which moves at a specific speed from the preset [Start].

Click [Auto Pan] on the left side of the screen to open the setting screen.

When you click the [Apply] button, the settings selected for [Mode] and [Speed] become valid on the viewer, and they are stored in the computer.

Mode

Select the [Mode] of the auto pan operation.

Right:
Rotate the camera horizontally in the right direction from the [Start].

Left:
Rotate the camera horizontally in the left direction from the [Start].

Return:
Move between [Start] and [Return] in the clockwise direction from the [Start] toward the [Return].
You can specify any random position as the start and return positions except under the following conditions.

Tilt angle of 90 ° or larger
(An error message appears if the angle is set to 90 ° or larger.)

Memo

If the zoom ratio between the [Start] and [Return] is different from each other, linked operations between zoom and pan/tilt may not be even.

Speed

Select the auto pan operation speed.

[Set values: Low, Middle, High]

Start, Return

Select the [Start] and [Return] (only during “Return”) of the operation. Operate the camera manually, decide on a position and click [Set] to register.

[Set]:
Complete the Auto Pan settings.

[GoTo]:
Move the camera to the registered position.

Memo

For details on the manual operation, see [PTZ Control].

[PTZ Control]

Auto Trace

For setting Auto Trace. This item stores and reproduces manual operation.

Click [Auto Trace] on the left side of the screen to open the setting screen.

As Auto Trace performs simple saving of manual operation, the position may be shifted during playback.

Digital Flip in [Auto Flip] cannot be used during Auto Trace recording.

State

[Record Start]:
The camera will start recording of Pan/Tilt and Zoom operations. (for approximately 30 seconds)

[Record Stop]:
Click this when a recording operation is complete.

Memo

For details on the manual operation, see [PTZ Control].

[PTZ Control]

[State] Display

The current status is displayed.

Standby:
The camera is on standby. [Record Stop] is invalid.

Recording:
The camera is recording. Click [Record Stop] to finish recording. “Completed” will be displayed.

Completed:
Recording is completed. After “Completed” is displayed for three seconds, “Standby” will be displayed.

Timeout:
30 seconds has passed since recording started. (Operation for the 30 seconds has been recorded.) After “Timeout” is displayed for three seconds, “Standby” will be displayed.

Memory Full:
The operation has exceeded the number of recordable operations. Further recording cannot be made even if it is within 30 seconds. (Operations before the limit are recorded.) After “Memory Full” is displayed for three seconds, “Standby” will be displayed.

Pan / Tilt / Zoom

Pan / Tilt operation:
Press the arrow buttons to move the display area in the direction indicated by the arrow. Release the button to stop the movement.
Press the [H] button to move to the home position.

Zoom operation:
Use this function to perform zoom operation on the display area.
[+]: Zooms in and enlarges an object.
[-]: Zooms out and reduces an object.

Scale display:
Displays the current magnification.

Memo

You can restrict the magnification of an object using the [+] button by altering the [EZoom Limit] settings.

EZoom Limit

You can manipulate zooming by rotating the mouse wheel.

You can operate the Pan, Tilt and Zoom functions using a mouse. If you click the mouse on the screen, the clicked spot will be the center of the display area. (Click on Center)

If “Click on Center” is not functioning properly, set the magnification to “100%” by clicking the magnifying glass icon at the bottom right of the window in the case of Internet Explorer 8, or the settings icon at the top right corner in the case of Internet Explorer 9. If doing so does not resolve the problem, set [Protocol] of Built-in Viewer to “HTTP(Unicast)”, and [Encoder] to “No.1”.

Built-in Viewer Screen Configuration