This screen displays the event. It is also used to display warnings only.
Display Screen in Camera Mode
TOPDisplay 0 screen
Appears only during warnings
Appears only during operation
Display 1 screen
Appears only during warnings
Display 2 screen
OK Mark
Displayed when OK mark has been appended.
Voltage/Battery Power
Displays the current status of the power supply in use.
Memo
Displayed in the Display 0 and Display 1 screens during warnings only.
Remaining Space on Media
Displays the remaining recording time of the SD cards in slot A and slot B separately.
:
Currently selected slot. (White card)
:
Write-protect switch of SD card is set.
!INVALID:
SD card cannot be read or written to, or restored.
!FORMAT:
SD card requires formatting.
!RESTORE:
SD card requires restoring.
!INCORRECT:
When Record Set is set to other than “AVCHD”/“SD”/“Web” with a Class 4 SD card inserted.
When the SD card is not supported.
When an SD card lower than Class 10 is inserted while in the XHQ mode.
!REC INH:
When attempting to record in 50i(HQ)/50i(SP) to an SD card recorded in AVCHD60i(HQ)/60i(SP) (or vice versa).
When attempting to record more than 4 GB while a media that does not support recording of more than 4 GB is inserted.
The following icons are displayed during FTP upload.
|
Icon |
Status |
|---|---|
 |
FTP transfer is in progress. |
 (Yellow) |
Error has occurred during FTP transfer. |
Memo
This item is not displayed when [Main Menu] 
[LCD/VF] [Display Settings] [Media Remain] is set to “Off”. However, warnings will be displayed.
Displayed on the Display 0 and Display 1 screens only in the case of warnings. (When the remaining time is shorter than 3 minutes)
The icons appear on all display screens in the following cases.
When recording is performed to only one of the slots while [Main Menu] [System] [Record Set] [Slot Mode] is set to “Dual”.
When recording is performed to only one of the slots while [Main Menu] [System] [Record Set] [Record Format] [System] is set to “HD+SD” or “HD+Web”.
The displayed time is an estimate.
Frame rate
Displayed as xx/yy fps (xx: recording frame rate, yy: playback frame rate) only when [Rec Mode] is set to “Variable Frame”.
Resolution
Displays the video image resolution.
Memo
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Record Format] is set to “Off”.
Frame Rate/Bit Rate
Displays the frame rate and bit rate in pairs.
Memo
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Record Format] is set to “Off”.
Audio Level Meter
Displays the audio levels of CH1 and CH2.
appears on the screen when in the Auto mode.
When [Main Menu] [System] [Record Set] [Rec Mode] is set to “Frame Rec”, “Interval Rec”, or “Variable Frame”, audio cannot be recorded and is indicated by the 
mark.
Memo
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Audio Meter] is set to “Off”.
GPS Mark
When [Main Menu] [System] [GPS] is set to “On”, the signal reception status is displayed.
Memo
The display changes according to the signal reception sensitivity. If signals cannot be received, the 
mark appears in yellow.
This item is not displayed when [GPS] is set to “Off”.
Volume Operation Indicator
Displayed when there are changes made to the volume of the headphone, speaker (0 to 15), and the values of LCD BRIGHT, PEAKING (-10 to +10).
Memo
There is no audio output from the speaker in Camera mode.
Flash Band Correction Mark
This item is displayed when [Main Menu] [Camera Function] [Flash Band Correction] is set to “On”.
Image Stabilizer Mark
Displayed when the image stabilizer is ON.
:
When [Level] of [OIS] is set to “Normal”.
:
When [Level] of [OIS] is set to “High”.
Memo
If image stabilizer is set to “OFF” when the Display 0 screen is displayed, 
appears for 3 seconds.
Displayed in the Display 0 screen only when there is a change.
White Balance Mode
Displays the current white balance mode.
(*****K indicates color temperature)
A<*****K>:
When the white balance is set to Auto A.
B<*****K>:
When the white balance is set to Auto B.
P<*****K>:
When the white balance is set to Preset.
<FAW>:
During Full Auto White Balance mode.
<FAW>:
When [AE LOCK] is set to “On” during Full Auto White Balance mode.
Memo
Displayed in the Display 0 screen only when there is a change.
Shutter
The current shutter speed is displayed when the shutter is set to “On”.
is displayed when the [FULL AUTO] switch is set to “ON” to enable Full Auto shooting mode, or when the [SHUTTER] button is pressed to enable automatic shutter mode.
Memo
The variable range of the shutter speed varies according to the video format settings.
Displayed in the Display 0 screen only when there is a change.
If the shutter speed is not displayed, the shutter is OFF.
Iris F-Number
Displays F-number of the lens iris.
Gain
Displays the gain value.
is displayed in the ALC mode during Manual shooting.
is displayed when AE LOCK is set to “ON”.
“LUX30” or “LUX36” is displayed when in the low-light shooting mode.
Memo
Displayed in the Display 0 screen only when there is a change.
AE Level
Appears when the AE function is activated, and [Main Menu] [Camera Function] [AE Level] is set to a value other than “Normal”.
When operated while manual operation is disabled, “AE” blinks for about 5 seconds.
When face detection is enabled and [Face Detect] is set to “AF&AE”, 
appears on the left side of “AE”.
ND Filter Position
Displays the current ND filter position.
Memo
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [ND Filter] is set to “Off”.
Displayed in the Display 0 screen only when there is a change.
Focus Display
Displays the value of the focal length during manual focus.
is displayed during Auto Focus.
When face detection is enabled, appears on the left side of .
If [Main Menu] [Camera Function] [AF Assist] is set to “Area”, the 
icon appears on the left side of .
Memo
You can specify whether to display the focus value (“Feet”/“Meter”) or turn off the display in [Main Menu] [LCD/VF] [Display Settings] [Focus].
This item will not be displayed when “Off” is selected.
Displayed in the Display 0 screen only when there is a change.
Focus Assist
“FOCUS” is displayed when auto focus is activated.
When ACCU-Focus is enabled, “ACCU-FOCUS” blinks for about 10 seconds while Focus Assist starts up, after which the “FOCUS” indicator lights up.
If recording starts while [ACCU-Focus] is active, [ACCU-Focus] will be forcibly deactivated.
Memo
Displayed in the Display 0 screen only when there is a change.
Luminance Information
Displayed when the Spot Meter function is activated.
MAX:
Maximum luminance
MIN:
Minimum luminance
Date/Time Display
Displays the current date and time.
Memo
The date/time display style can be specified in [Main Menu] [LCD/VF] [Display Settings] [Date Style]/[Time Style].
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Date/Time] is set to “Off”.
When [Main Menu] [System] [Record Set] [Time Stamp] is set to “On”, this item is not displayed.
Zoom Display
Displays the zoom position. (Zoom bar or value)
The zoom bar will only be displayed for 3 seconds after the zoom operation is activated.
The value will always be displayed. (0 to 99)
Memo
You can specify the display method (Number/Bar) and whether to turn off the display in [LCD/VF] [Display Settings] “Zoom”.
This item will not be displayed when “Off” is selected.
Displayed in the Display 0 screen only when there is a change.
Network Connection Icon
When [Main Menu] [System] [Network] is set to “On(SDI Off)” or “On(HDMI Off)”, the network connection status is displayed.
This icon is not displayed when “Off” is selected.
|
Icon |
Status |
|---|---|
 (Blink) |
Connection is not established (starting up, preparing for connection) |
 (Yellow) |
Connection is not established (preparing for connection) |
|
Connection is established |
 |
When a USB adapter different from the connection settings is detected |
|
(No display) |
When an incompatible USB adapter is detected, or when [Network] is set to “Off” |
Memo
When using a cellular adapter that supports the display of LTE connection, “LTE” is displayed to the left of the icon above when an LTE connection is detected.
Time Code ( 
)/User’s Bit ( 
) Display
Displays the time code (hour: minute: second: frame) or user’s bit data.
Example of time code display:
Colon (:) denotes non-drop frames and dot (.) denotes drop frames.
Example of user’s bit display:
Memo
You can specify whether to display the time code, user’s bit, or turn off the display in [LCD/VF] [Display Settings] [TC/UB].
This item will not be displayed when “Off” is selected.
Time Code Lock Indicator
When the built-in time code generator is synchronized to the external time code data input during the synchronization of time code with another camera recorder, lights up.
Live streaming mark
When [Main Menu] [System] [Network]/[Settings] [Live Streaming Set] [Live Streaming] is set to “On”, the distribution status is displayed.
|
Icon |
Status |
|---|---|
 (Red) |
Distribution in progress (good connection quality) |
 (Red) |
Distribution in progress (poor connection quality) |
 (Yellow) |
Connection pending or connection failed |
Event/Warning Display Area
Displays error messages.
Media Status
----:
No card found in the selected slot
STBY:
Recording standby
REC:
Recording
REVIEW:
Clip Review
STBY 
:
Pre Rec recording standby
REC :
Pre Rec recording
STBY 
:
Clip Continuous Rec recording standby
REC :
Clip Continuous Rec recording
STBY (displayed in yellow):
Clip Continuous Rec recording pause
STBY 
:
Interval Rec recording standby
STBY (displayed in red):
Interval recording pause
REC :
Interval Rec recording
STBY 
:
Frame Rec recording standby
REC :
Frame Rec recording
STBY (displayed in yellow):
Frame Rec recording pause
STOP:
Unable to record to the card in the slot
P.OFF:
Power OFF
Dual Rec/Backup Rec Display
“DUAL” is displayed in the Dual Rec mode and “BACKUP” is displayed in the Backup Rec mode.
Memo
This item is not displayed when [Slot Mode] is set to “Series”.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Media Remain] is set to “Off”. However, warnings will be displayed.
Displayed in the Display 0 and Display 1 screens during warnings only. (When the remaining time is shorter than 3 minutes)