This screen displays the event. It is also used to display warnings only.
Display Screen in Camera Mode
TOPDisplay 0 screen
Appears only during warnings
Appears only during operation
Display 1 screen
Appears only during warnings
Display 2 screen
Operation Lock Icon
Appears when the operation lock feature is turned on.
Voltage/Battery Power
Displays the current status of the power supply in use.
Displayed in the Display 0 and Display 1 screens during warnings only.
Remaining Space on Media
Displays the remaining recording time of the SD cards in slot A and slot B separately.
:
Currently selected slot. (White card)
:
Write-protect switch of SD card is set.
!INVALID:
SD card cannot be read or written to, or restored.
!FORMAT:
SD card requires formatting.
!RESTORE:
SD card requires restoring.
!INCORRECT:
When [Rec Mode] is set to other than “AVCHD”/“SD”/“Web” with a Class 4 SD card inserted.
When the SD card is not supported.
!REC INH:
When attempting to record in 50p or 50i to an SD card recorded in [AVCHD]60p or 60i (or vice versa).
When attempting to record more than 4 GB while a media that does not support recording of more than 4 GB is inserted.
When an SD card lower than Class 10 is inserted while in the XHQ mode.
The following icons are displayed during FTP upload.
Icon |
Status |
---|---|
FTP transfer is in progress. |
|
(Yellow) |
Error has occurred during FTP transfer. |
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Media Remain] is set to “Off”. However, warnings will be displayed.
Displayed on the Display 0 and Display 1 screens only in the case of warnings. (When the remaining time is shorter than 3 minutes)
The icons appear on all display screens in the following cases.
When recording is performed to only one of the slots while [Main Menu] [System] [Record Set] [Slot Mode] is set to “Dual”.
When recording is performed to only one of the slots while [Main Menu] [System] [Record Set] [Record Format] [System] is set to “HD+SD” or “HD+Web”.
The displayed time is an estimate.
Frame rate
Frame rate/SDI IN
Displayed as xx/yy fps (xx: recording frame rate, yy: playback frame rate) only when [Rec Mode] is set to “Variable Frame”.
“SDI IN ” is displayed when a device is connected to the [SDI IN] terminal, and [System] [Record Set] [Record Format] [System] is set to “HD(SDI In)” or “SD(SDI In)”.
Resolution
Displays the video image resolution.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Record Format] is set to “Off”.
Frame Rate/Bit Rate
Displays the frame rate and bit rate in pairs.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Record Format] is set to “Off”.
Audio Level Meter
Displays the audio levels for CH-1 to CH-4.
appears on the screen when in the Auto mode.
When [Rec Mode] [Rec Mode] is set to “Frame Rec”, “Interval Rec”, or “Variable Frame”, audio cannot be recorded and the audio level meter is grayed out.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Audio Meter] is set to “Off”.
Histogram Display
This item is displayed when [Main Menu] [LCD/VF] [Display Settings] [Histogram] is set to “On”.
When the histogram is displayed, the audio level meter display is turned off temporarily.
GPS Mark
When [System] [GPS] is set to “On”, the signal reception status is displayed.
The display changes according to the signal reception sensitivity. If signals cannot be received, the mark appears in yellow.
This item is not displayed when [GPS] is set to “Off”.
Volume Operation Indicator
This item is displayed when the LCD BRIGHT and LCD PEAKING values (-10 to +10) are changed.
Flash Band Correction Mark
This item is displayed when [Main Menu] [Camera Function] [Flash Band Correction] is set to “On”.
Image Stabilizer Icon
Displayed when the image stabilizer is ON.
:
When [Level] of [OIS] is set to “Normal”.
:
When [Level] of [OIS] is set to “High”.
If image stabilizer is set to “OFF” when the Display 0 screen is displayed, appears for 3 seconds.
Displayed in the Display 0 screen only when there is a change.
White Balance Mode
Displays the current white balance mode.
(*****K indicates color temperature)
A<*****K>:
When the white balance is set to Auto A.
B<*****K>:
When the white balance is set to Auto B.
P<*****K>:
When the white balance is set to Preset.
<FAW>:
During Full Auto White Balance mode.
<FAW>:
When [AE LOCK] is set to “On” during Full Auto White Balance mode.
Displayed in the Display 0 screen only when there is a change.
Shutter
The current shutter speed is displayed when the shutter is set to “On”.
is displayed when the [FULL AUTO ON/OFF] switch is set to “ON” to enable Full Auto shooting mode, or when the [SHUTTER] button is pressed to enable automatic shutter mode.
The variable range of the shutter speed varies according to the video format settings.
Displayed in the Display 0 screen only when there is a change.
If the shutter speed is not displayed, the shutter is OFF.
Iris F-Number
Displays F-number of the lens iris.
Gain
Displays the gain value.
is displayed in the ALC mode during Manual shooting.
is displayed when AE LOCK is set to “ON”.
“LUX30” or “LUX36” is displayed when in the low-light shooting mode.
Displayed in the Display 0 screen only when there is a change.
AE Level
Appears when the AE function is activated, and [Main Menu] [Camera Function] [AE Level] is set to a value other than “Normal”.
When operated while manual operation is disabled, “AE” blinks for about 5 seconds.
When face detection is enabled and [Face Detect] is set to “AF&AE”, appears on the left side of “AE”.
ND Filter Position
Displays the current ND filter position.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [ND Filter] is set to “Off”.
Displayed in the Display 0 screen only when there is a change.
Focus Display
Displays the approximate distance to the subject in focus during manual focus.
is displayed during Auto Focus.
When face detection is enabled, appears on the left side of .
If [Main Menu] [Camera Function] [AF Assist] is set to “Area”, the icon appears on the left side of .
You can specify the display method (Feet/Meter) in [Main Menu] [LCD/VF] [Display Settings] [Focus].
This item will not be displayed when “Off” is selected.
Displayed in the Display 0 screen only when there is a change.
Focus Assist
“FOCUS” is displayed when auto focus is activated.
When ACCU-Focus is enabled, “ACCU-FOCUS” blinks for about 10 seconds while Focus Assist starts up, after which the “FOCUS” indicator lights up.
If recording starts while [ACCU-Focus] is active, [ACCU-Focus] will be forcibly deactivated.
Displayed in the Display 0 screen only when there is a change.
Luminance Information
Displayed when the Spot Meter function is activated.
MAX:
Maximum luminance
MIN:
Minimum luminance
Date/Time Display
Displays the current date and time.
The date/time display style can be specified in [Main Menu] [LCD/VF] [Display Settings] [Date Style]/[Time Style].
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Date/Time] is set to “Off”.
When [Main Menu] [System] [Record Set] [Time Stamp] is set to “On”, this item is not displayed.
Zoom Display
Displays the zoom position. (Zoom bar or value)
The zoom bar will only be displayed for 3 seconds after the zoom operation is activated.
The value will always be displayed. (0 to 99)
You can specify the display method (Number/Bar) in [LCD/VF] [Display Settings] “Zoom”.
This item will not be displayed when “Off” is selected.
Displayed in the Display 0 screen only when there is a change.
Network Connection Icon
When [Main Menu] [System] [Network] is set to “On(SDI Off)” or “On(HDMI Off)”, the network connection status is displayed.
This icon is not displayed when “Off” is selected.
Icon |
Status |
---|---|
(Blink) |
Connection is not established (starting up, preparing for connection) |
(Yellow) |
Connection is not established (preparing for connection) |
Connection is established |
|
When a USB adapter different from the connection settings is detected |
|
(No display) |
When an incompatible USB adapter is detected, or when [Network] is set to “Off” |
When a cellular adapter that supports LTE connection display is in use, “LTE” will appear to the left of the above icon when LTE connection is detected.
Time Code ( )/User’s Bit ( ) Display
Displays the time code (hour: minute: second: frame) or user’s bit data recorded in the SD card being played back.
Example of time code display:
Colon (:) denotes non-drop frames and dot (.) denotes drop frames.
Example of user’s bit display:
You can specify whether to display the time code, user’s bit, or turn off the display in [LCD/VF] [Display Settings] [TC/UB].
This item will not be displayed when “Off” is selected.
Time Code Lock Indicator
When the built-in time code generator is synchronized to the external time code data input during the synchronization of time code with another camera recorder, lights up.
Live streaming mark
When [Main Menu] [System] [Network]/[Settings] [Live Streaming Set] [Live Streaming] is set to “On”, the distribution status is displayed.
Icon |
Status |
---|---|
(Red) |
Distribution in progress (good connection quality) Blinks when distribution starts or stops |
(Red) |
Distribution in progress (poor connection quality) |
(Yellow) |
Waiting for connection (during RTSP/RTP) or connection failed |
Event/Warning Display Area
Displays error messages.
Media Status
----:
A card is not detected in the selected slot, and [Tally System] is also not set to “Studio”
STBY:
Recording standby
REC:
Recording
REVIEW:
Clip Review
STBY :
Pre Rec recording standby
REC :
Pre Rec recording
STBY :
Clip Continuous Rec recording standby
REC :
Clip Continuous Rec recording
STBY (displayed in yellow):
Clip Continuous Rec recording pause
STBY :
Interval Rec recording standby
STBY (displayed in red):
Interval recording pause
REC :
Interval Rec recording
STBY :
Frame Rec recording standby
REC :
Frame Rec recording
STBY (displayed in yellow):
Frame Rec recording pause
STOP:
Unable to record to the card in the slot
P.OFF:
Power OFF
:
During clip cutter recording (displayed for 3 seconds)
CALL:
Receiving call signals from an external device, such as a remote control unit
PGM:
Receiving program signals from an external device, such as a remote control unit
PVW:
Receiving preview signals from an external device, such as a remote control unit
Dual Rec/Backup Rec Display
“DUAL” is displayed in the Dual Rec mode and “BACKUP” is displayed in the Backup Rec mode.
This item is not displayed when [Slot Mode] is set to “Series”.
This item is not displayed when [Main Menu] [LCD/VF] [Display Settings] [Media Remain] is set to “Off”. However, warnings will be displayed.
OK Mark
Displayed when OK mark has been appended.